Logo

C1277 Engine Trouble Code

C1277 Engine

When you check engine light came on code C1277 the reason should be Engine Light ON (or Service Engine Soon Warning Light). However your vehicle's manufacturer may have a different definition for the C1277 OBD-II Diagnostic Chassis (C) Trouble Code. So you should chech it on our car models.

When the DTC check engine light comes C1277 code on the first you can check is the gas related maybe gas cap. Pull over, retighten it, and take a look at the cap to see if it has any cracks inside. Go on driving and to see if the check engine light turns off automaticly. On the other hand, you can buy a gas cap for about $4.5 at an auto parts store. All you need to do is take the old one take off and take on the new one. If you've already bought it to the store, you might as well just replace the cap. While not car-threatening, it's good to take care of this right away to improve gas mileage/km.

C1277 Code Meaning :

C
OBD-II Diagnostic Chassis (C) Trouble Code For Engine
1
Fuel And Air Metering
2
Ambient Air Temperature Sensor Circuit Low
7
Injection lump Fuel Metering Control 'B' High (Cam/Rotor/Injector)
7
Crankshaft Position Sensor B Circuit Malfunction

The oxygen (02) sensors on your car measure the oxygen in the exhaust to determine how rich or lean the ratio of fuel and air are in the cylinders. Optimizing this mixture means better fuel economy and fewer exhaust emissions.

C1277 OBD-II Diagnostic Chassis (C) Trouble Code Description

C1277 OBD-II Trouble Code The Electronic Brake Control Module (EBCM) and the Powertrain Control Module ( C1277 code. Ambient Air Temperature Sensor Circuit Low and Injection lump Fuel Metering Control 'B' High (Cam/Rotor/Injector) causes most of code C1277.

Reason For C1277 Code

The reason of C1277 OBD-II Engine Trouble Code is Ambient Air Temperature Sensor Circuit Low.

C1277 DTC reports a sensor fault, replacement of the sensor is unlikely to resolve the underlying problem. The engine error is most likely to be caused by the systems that the sensor is monitoring, but might even be caused by the wiring to the sensor itself.

How To Repair C1277 Code

Before starting let's see C1277 repairing process steps:

  • Qualified technicians will begin by using a scan tool to access C1277 code stored in the ECU.
  • Technicians will note C1277 code present and any freeze frame data associated with them.
  • After all, if you sure the engine trouble is finished, the code will be cleared.

The reductant injector is part of the system that reduces the gas that is expelled through either the catalytic converter in gas engines, or the particulate filter in diesel engines. There are sensors in the exhaust system, used by the reductant injector to input voltage readings to the PCM.

C1277 code is stored again, the mechanic will perform a visual inspection of the pressure control solenoid and related systems. If any circuits or connections are damaged or loose, they will resolve these issues and move on to retest the system.

Sometimes C1277 code comes with C127700 code.

Diagnosis Of Engine Error OBD Code C1277

It's essential to diagnose this trouble code. Then are some way which a handyperson should follow for diagnosing the problem that started a C1277 trouble code to be stored

The first step is introductory and is about reacquiring all the canons that have been set. For this, the individual scanner will have to be plugged into the individual harborage of your vehicle. Make sure you indurate frame the data. Any canons that were set previous to the C1277 code will have to be sorted first, as they may have been the reason for the law to set in the first place. It's always good to rule that out.

The coming step is to run a introductory examination of all the electrical circuits, connectors, wiring etc for damages similar as becks, erosion, fraudulent legs etc. All of these will have to be repaired or replaced. After that's sorted, clear the canons and go on a test drive to see if it resets. In case it resets, you'll have to continue your opinion. Depending on your vehicle you may have a vacuum operated selector or a vacuum solenoid if it's electrically actuated. In the case of the former, a hand held vacuum pump will have to be used to testit.The purpose is to see if the internal stopcock is getting turned by the selector, motor or solenoid. In order to do this, a command can be transferred to the system with scanner or by driving the vehicle under the special conditions that will spark the system. While this is passing keep an eye on the checkup tool data for the result.

All Engine Trouble Codes

All engine trouble codes with P, U, B and C engine codes.

Code Search

Please fill the "Code Box" to find engine fault code.

Example: 0140

Car Models :

Please select your car.

How To Read Engine Codes ?

Ways to read engine trouble codes.

How To Clear Check Engine Lights ?

Ways to clear check engine light on car panel.

Check Engine Light Dictionary

Ways to clear check engine light on car panel.